ADM242AR
아날로그 디바이스(주)
- Lifecycle
- Active
- Stock
- 6746 PCS
- Package
- SOIC-18
- Series
- 인터페이스 - 드라이브, 수신기, 트랜시버
ADM242AR과 ADM241LAR에 대한 심층 비교를 통해 두 제품의 사양 및 주요 특징에 대한 유용한 정보를 얻을 수 있습니다. RoHS 준수 여부, REACH 인증 상태, 시리즈, 장착 방식, 패키지 유형 및 기타 관련 특성을 포함한 중요한 요소들을 자세히 다룹니다. 두 제품의 차이점을 나란히 제시함으로써 부품 선택이 간소화되어 특정 용도에 가장 적합한 옵션을 쉽게 선택할 수 있습니다.
Replacement verdict
The ADM241LAR is a functionally compatible replacement candidate for the ADM242AR, sharing the same RS-232 transceiver function, dual driver/receiver channel count, and 16-pin SOIC package. Designers should validate the lower data rate (120 kbps vs 200 kbps) and confirm the reduced external capacitor configuration meets the target application's timing and charge-pump requirements before committing to production.
Rows are prioritized by design impact. Highlighted values require attention during substitution.
Key electrical and mechanical differences between the two devices
| Parameter | ADM242AR | ADM241LAR | Why it matters |
|---|---|---|---|
| Number of Drivers | 2 | 4 | Determines how many RS-232 transmit lines the device can drive; a functional substitute must match the required channel count. |
| Number of Receivers | 2 | 5 | Determines how many RS-232 receive lines are supported; mismatched receiver count affects interface compatibility. |
| Data Rate | 200 kbps | 120 kbps | Maximum signaling speed; must meet the baud rate requirements of the target serial link. |
| External Charge Pump Capacitors | 4 (0.1 µF) | 4 (0.1 µF) | Both require external capacitors for the internal charge pump; the count and value affect board layout and BOM. |
| Shutdown / Enable Control | Yes | Yes | Shutdown capability allows power savings when the interface is idle; both parts support it. |
| Operating Supply Voltage | 5 V | 5 V | Single 5 V supply compatibility is essential for direct substitution in existing designs. |
| Package | 24-pin SOIC (wide) | 28-pin SOIC (wide) | Footprint and pin count must match the PCB layout; different packages require board redesign. |
| Operating Temperature Range | -40 °C to +85 °C | -40 °C to +85 °C | Industrial temperature range ensures reliable operation across the application's environmental conditions. |
Send your BOM and application constraints for technical and sourcing review.
Use manufacturer datasheets as the final authority.
| Specification | ADM242AR | ADM241LAR |
|---|---|---|
| Supplier | - | Analog Devices Inc.,Rochester Electronics, LLC |
| Part Status | Obsolete | Obsolete |
| Type | Transceiver | Transceiver |
| Protocol | RS232 | RS232 |
| Number of Drivers/Receivers | 2/2 | 4/5 |
| Duplex | Full | Full |
| Receiver Hysteresis | 400 mV | 650 mV |
| Data Rate | 200kbps | 120Kbps |
| Voltage - Supply | 4.5V ~ 5.5V | 4.75V ~ 5.25V |
| Operating Temperature | -40°C ~ 85°C | -40°C ~ 85°C |
| Mounting Type | Surface Mount | Surface Mount |
Both are dual-channel RS-232 line drivers/receivers from Analog Devices in a 24-lead SOIC package. The ADM242AR integrates two charge pump capacitors (using 0.1 µF external capacitors) and operates from a single +5 V supply, while the ADM241LAR requires four external 0.1 µF charge pump capacitors. The ADM241LAR is specified for a lower data rate (up to 120 kbps) and features a low-power shutdown mode, whereas the ADM242AR supports data rates up to 200 kbps.
No. Although both devices are housed in a 24-lead SOIC package, their pinouts differ. The ADM242AR uses an internal charge pump architecture requiring only two external capacitors, which changes the function of several pins compared to the ADM241LAR, which requires four external charge pump capacitors. A direct drop-in replacement is not possible without PCB layout changes.
The ADM242AR is specified for data rates up to 200 kbps. The ADM241LAR is specified for data rates up to 120 kbps. Both meet or exceed the EIA-232-E and V.28 specifications.
Yes. Both the ADM242AR and ADM241LAR operate from a single +5 V ±10% power supply and generate the required RS-232 voltage levels internally via on-chip charge pump converters.
Yes. The ADM241LAR includes a low-power shutdown mode that reduces supply current to typically 15 µA when the device is not in use. The ADM242AR does not provide this shutdown feature.
The ADM242AR requires only two external 0.1 µF charge pump capacitors. The ADM241LAR requires four external 0.1 µF charge pump capacitors. This difference affects board space and layout complexity.
The ADM242AR typically draws 8 mA of supply current. The ADM241LAR typically draws 6 mA in normal operation and approximately 15 µA in shutdown mode. These values are based on manufacturer datasheet specifications.
No. Due to differences in pinout, external capacitor count, data rate, and shutdown functionality, the two devices are not interchangeable without redesigning the PCB layout and verifying all electrical parameters against the target application requirements.