ADM4851ARZ vs ADM4853ARZ

ADM4851ARZ과 ADM4853ARZ에 대한 심층 비교를 통해 두 제품의 사양 및 주요 특징에 대한 유용한 정보를 얻을 수 있습니다. RoHS 준수 여부, REACH 인증 상태, 시리즈, 장착 방식, 패키지 유형 및 기타 관련 특성을 포함한 중요한 요소들을 자세히 다룹니다. 두 제품의 차이점을 나란히 제시함으로써 부품 선택이 간소화되어 특정 용도에 가장 적합한 옵션을 쉽게 선택할 수 있습니다.

Technical review by ETEI Component Engineering Source: manufacturer documentation

Replacement verdict

Compatible functional replacement candidate

The ADM4853ARZ and ADM4851ARZ are both half-duplex RS-485/RS-422 transceivers in the same 8-lead SOIC package with identical supply voltage and pin function, making the ADM4853ARZ a viable functional replacement candidate for the ADM4851ARZ in most designs. However, the two devices differ in their data rate and slew-rate characteristics, so signal integrity and bus-length requirements should be validated before substitution.

Package Type High match
Supply Voltage High match
Data Rate Validation required
Slew Rate Validation required

Parts at a glance

Part A

ADM4851ARZ

아날로그 디바이스(주)

Lifecycle
Active
Stock
4442 PCS
Package
SOIC-8
Series
인터페이스 - 드라이브, 수신기, 트랜시버
Part B

ADM4853ARZ

아날로그 디바이스(주)

Lifecycle
Active
Stock
6517 PCS
Package
SOIC-8
Series
인터페이스 - 드라이브, 수신기, 트랜시버

Key differences

Rows are prioritized by design impact. Highlighted values require attention during substitution.

Key electrical and mechanical differences between the two devices

Parameter ADM4853ARZ ADM4851ARZ Why it matters
Data Rate 10 Mbps 500 kbps Maximum signaling speed; a 20x difference determines whether the part suits high-speed or low-speed buses.
Duplex Mode Full duplex Half duplex Full duplex allows simultaneous transmit/receive on separate pairs, while half duplex shares one pair; this changes bus topology and pin usage.
Number of Drivers/Receivers 1 driver / 1 receiver 1 driver / 1 receiver Confirms the transceiver channel count; identical here, so channel capacity is not a differentiator.
Receiver Input Impedance (Unit Loads) 1 unit load (standard) 1 unit load (standard) Determines how many nodes can share the bus; both are standard 1-unit-load devices supporting up to 32 nodes.
Supply Voltage 5 V 5 V Operating supply rail; both require 5 V, so power supply design is compatible.
Operating Temperature Range -40 °C to +85 °C -40 °C to +85 °C Industrial temperature rating; identical ranges mean equivalent environmental robustness.
Package / Mounting 8-Lead SOIC (surface mount) 8-Lead SOIC (surface mount) Footprint and assembly compatibility; identical packages allow drop-in board replacement.
Fail-Safe Receiver Yes (open-circuit, short-circuit, idle-bus) Yes (open-circuit, short-circuit, idle-bus) Guarantees a defined logic output when the bus is undriven; both provide this, so behavior on floating lines is equivalent.
ESD Protection (Bus Pins) ±15 kV (HBM) ±15 kV (HBM) Bus-pin ESD robustness; identical ratings mean comparable field reliability.

Need help validating a replacement?

Send your BOM and application constraints for technical and sourcing review.

Full specification comparison

Use manufacturer datasheets as the final authority.

Specification ADM4851ARZ ADM4853ARZ
Part Status Active Active
Type Transceiver Transceiver
Protocol RS422, RS485 RS422, RS485
Number of Drivers/Receivers 1/1 1/1
Duplex Half Half
Receiver Hysteresis 20 mV 20 mV
Data Rate 500kbps 10Mbps
Voltage - Supply 4.75V ~ 5.25V 4.75V ~ 5.25V
Operating Temperature -40°C ~ 85°C -40°C ~ 85°C
Mounting Type Surface Mount Surface Mount

Frequently asked questions

What are the key differences between the ADM4853ARZ and ADM4851ARZ?

Both are 5 V, half-duplex RS-485/RS-422 transceivers in an 8-lead SOIC package, but they differ in data rate and slew-rate behavior. The ADM4853ARZ is specified for data rates up to 10 Mbps, while the ADM4851ARZ is a limited-slew-rate version specified for data rates up to 500 kbps, which reduces EMI and improves signal integrity on long cables.

Are the ADM4853ARZ and ADM4851ARZ pin-compatible?

Yes. Both devices are offered in the same 8-lead SOIC (R-8) package with the same pinout (RO, RE, DE, DI, GND, A, B, VCC), so they are pin-compatible and share the same PCB land pattern.

Can the ADM4853ARZ be used as a drop-in replacement for the ADM4851ARZ?

Electrically they are pin-compatible, but the ADM4853ARZ supports up to 10 Mbps with faster output edges, whereas the ADM4851ARZ is slew-rate limited to 500 kbps. Substitution is acceptable only if the higher data rate and faster edges of the ADM4853ARZ do not cause EMI or signal-integrity issues in the target design; otherwise the ADM4851ARZ should be retained.

What supply voltage and bus interface do these transceivers support?

Both the ADM4853ARZ and ADM4851ARZ operate from a single 5 V supply and provide half-duplex RS-485/RS-422 differential bus signaling, with a driver output and receiver input compliant with the RS-485/RS-422 standards.

How many nodes can be connected on the bus with these transceivers?

Both devices are specified as 1/8-unit-load (1/8 UL) receivers, allowing up to 256 transceivers to be connected on a single RS-485 bus, provided the bus is properly terminated and biased.

Do the ADM4853ARZ and ADM4851ARZ include fail-safe receiver behavior?

Yes. Both devices feature a fail-safe receiver that guarantees a known logic-high output when the bus inputs are open, shorted, or terminated but undriven, preventing indeterminate output states.

What is the operating temperature range for these parts?

Both the ADM4853ARZ and ADM4851ARZ are specified for the industrial temperature range of −40 °C to +85 °C, making them suitable for industrial networking and control applications.

Which part should be selected for long-cable or noisy industrial networks?

The ADM4851ARZ is generally preferred for long-cable or EMI-sensitive networks because its limited slew rate (500 kbps maximum) reduces radiated emissions and reflections. The ADM4853ARZ should be selected only when data rates up to 10 Mbps are required and the cabling and layout can support the faster edges.