ADM485EARZ vs ADM4850AR

ADM485EARZ과 ADM4850AR에 대한 심층 비교를 통해 두 제품의 사양 및 주요 특징에 대한 유용한 정보를 얻을 수 있습니다. RoHS 준수 여부, REACH 인증 상태, 시리즈, 장착 방식, 패키지 유형 및 기타 관련 특성을 포함한 중요한 요소들을 자세히 다룹니다. 두 제품의 차이점을 나란히 제시함으로써 부품 선택이 간소화되어 특정 용도에 가장 적합한 옵션을 쉽게 선택할 수 있습니다.

Technical review by ETEI Component Engineering Source: manufacturer documentation

Replacement verdict

Compatible functional replacement candidate

The ADM485EARZ and ADM4850AR are both half-duplex RS-485/RS-422 transceivers in 8-lead SOIC packages with comparable supply voltage and data-rate classes, making the ADM4850AR a viable functional substitute for the ADM485EARZ in many designs. However, the two parts differ in ESD protection level, fail-safe receiver behavior, and specified operating temperature range, so the replacement should be validated against the target application's robustness and environmental requirements before adoption.

Interface Protocol Validation required
Package Type High match
ESD Protection Level Validation required
Operating Temperature Range Validation required

Parts at a glance

Part A

ADM485EARZ

아날로그 디바이스(주)

Lifecycle
Active
Stock
3013 PCS
Package
SOIC-8
Series
인터페이스 - 드라이브, 수신기, 트랜시버
Part B

ADM4850AR

아날로그 디바이스(주)

Lifecycle
Active
Stock
9264 PCS
Package
SOIC-8
Series
인터페이스 - 드라이브, 수신기, 트랜시버

Key differences

Rows are prioritized by design impact. Highlighted values require attention during substitution.

Key electrical and mechanical differences between the two devices

Parameter ADM485EARZ ADM4850AR Why it matters
Data Rate 2.5 Mbps 250 kbps Determines the maximum communication speed the transceiver can support; a faster part can replace a slower one in most designs but not vice versa.
Duplex Mode Half-duplex Half-duplex Defines whether the device can transmit and receive simultaneously; both are half-duplex, so bus topology compatibility is preserved.
Number of Drivers/Receivers 1/1 1/1 Indicates the transceiver channel count; matching 1/1 configuration ensures direct functional substitution on a single RS-485 bus.
Supply Voltage 5 V 5 V Both operate from a 5 V rail, so the same power supply design can be reused without modification.
Operating Temperature Range -40°C to +85°C -40°C to +85°C Confirms both parts are rated for industrial temperature environments, ensuring reliability under the same operating conditions.
ESD Protection (Bus Pins) ±15 kV (HBM) ±15 kV (HBM) Higher ESD tolerance improves robustness in harsh field environments; matching ratings mean equivalent protection levels.
Fail-Safe Receiver Yes (open/short circuit) Yes (open/short circuit) Fail-safe receivers guarantee a defined logic output when the bus is idle or floating, preventing spurious data in multi-node networks.
Package / Mounting 8-SOIC (Surface Mount) 8-SOIC (Surface Mount) Identical package and footprint allow drop-in replacement on the same PCB without layout changes.
Driver Output Voltage (Loaded) 2.0 V min (54 Ω load) 2.0 V min (54 Ω load) Ensures adequate differential signal amplitude for reliable RS-485 communication over long cables; matching values confirm equivalent drive strength.

Need help validating a replacement?

Send your BOM and application constraints for technical and sourcing review.

Full specification comparison

Use manufacturer datasheets as the final authority.

Specification ADM485EARZ ADM4850AR
Supplier - Rochester Electronics, LLC
Part Status Active Obsolete
Type Transceiver Transceiver
Protocol RS422, RS485 RS422, RS485
Number of Drivers/Receivers 1/1 1/1
Voltage - Supply 4.75V ~ 5.25V 4.75V ~ 5.25V
Mounting Type Surface Mount Surface Mount
Duplex Half -
Receiver Hysteresis 70 mV -
Data Rate 2.5Mbps -
Operating Temperature -40°C ~ 85°C -

Frequently asked questions

What are the key differences between the ADM485EARZ and ADM4850AR?

The ADM485EARZ is a 5 V, half-duplex RS-485/RS-422 transceiver in an 8-lead SOIC package with enhanced ESD protection (±15 kV IEC 61000-4-2 on bus pins) and a data rate up to 5 Mbps. The ADM4850AR is a 5 V, half-duplex RS-485/RS-422 transceiver in an 8-lead SOIC package with a data rate up to 2.5 Mbps and standard ESD protection. The ADM485EARZ is a newer enhanced-ESD variant, while the ADM4850AR is an older standard variant.

Are the ADM485EARZ and ADM4850AR pin-compatible?

Yes. Both devices are offered in an 8-lead SOIC package with the same pinout (RO, RE, DE, DI, GND, A, B, VCC), so they are pin-compatible and share the same PCB land pattern.

Can the ADM485EARZ directly replace the ADM4850AR in an existing design?

In most cases yes, because both are 5 V half-duplex RS-485 transceivers in the same 8-lead SOIC package with identical pin functions. However, the ADM485EARZ supports a higher data rate (up to 5 Mbps vs. 2.5 Mbps) and offers enhanced ESD protection, so the replacement should be validated against the target design's data rate, bus loading, and ESD requirements using the respective manufacturer datasheets.

What are the maximum data rates of the ADM485EARZ and ADM4850AR?

The ADM485EARZ supports data rates up to 5 Mbps. The ADM4850AR supports data rates up to 2.5 Mbps.

What ESD protection do the ADM485EARZ and ADM4850AR provide on the bus pins?

The ADM485EARZ provides enhanced ESD protection of ±15 kV using the IEC 61000-4-2 Air-Gap Discharge method and ±8 kV using the IEC 61000-4-2 Contact Discharge method on the RS-485 bus pins. The ADM4850AR provides standard ESD protection; designers should consult the ADM4850AR datasheet for its specified ESD ratings before relying on a particular level.

Do both devices operate from a single 5 V supply?

Yes. Both the ADM485EARZ and ADM4850AR are specified for operation from a single 5 V supply and are half-duplex RS-485/RS-422 transceivers.

What package do the ADM485EARZ and ADM4850AR use?

Both devices are available in an 8-lead SOIC package (the "RZ" and "AR" suffixes denote the SOIC package option).

Which device should be selected for a new design requiring higher speed and robust ESD protection?

The ADM485EARZ is the appropriate choice when data rates up to 5 Mbps and enhanced ±15 kV IEC 61000-4-2 ESD protection on the bus pins are required. The ADM4850AR is limited to 2.5 Mbps and standard ESD protection, so it is better suited to lower-speed applications where enhanced ESD robustness is not needed.