사양
| 속성 | 가치 |
| Supplier | Nexperia USA Inc. |
| Package / Case | Tape & Reel (TR),Cut Tape (CT) |
| Part Status | Active |
| Transistor Type | NPN - Pre-Biased |
| Current - Collector(Ic)(Max) | 100 mA |
| Voltage - Collector Emitter Breakdown(Max) | 50 V |
| Resistor - Base(R1) | 10 kOhms |
| Resistor - Emitter Base(R2) | 10 kOhms |
| DC Current Gain(h FE)(Min) @ Ic Vce | 30 @ 5mA, 5V |
| Vce Saturation(Max) @ Ib Ic | 150mV @ 500µA, 10mA |
| Current - Collector Cutoff(Max) | 1µA |
| Frequency - Transition | 230 MHz |
| Power - Max | 250 mW |
| Mounting Type | Surface Mount |
개요
Description
PDTC114ET is an NPN digital transistor with a built‑in base resistor, designed to be driven directly from a microcontroller. The “ET” variant is a RoHS/compliant version; the “215” suffix is likely a package/lot or option code and is not a separate electrical spec. Key idea: it simplifies driving a load (LEDs, relays, small motors) by eliminating an external base resistor.
Typical use:
- Load connected between Vcc and the transistor’s collector; MCU output drives the base via the built‑in resistor.
- Provides a quick, compact switch with fewer components.
General (variant‑dependent) specs:
- Vce: ~30–35 V
- Ic: tens to around 100 mA
- Built‑in base bias improves tamper resistance to noise and simplifies design
Note: exact ratings and pinout depend on the specific PDTC114ET variant. For precise electrical specs and the meaning of “215,” consult the manufacturer’s datasheet.
Typical use:
- Load connected between Vcc and the transistor’s collector; MCU output drives the base via the built‑in resistor.
- Provides a quick, compact switch with fewer components.
General (variant‑dependent) specs:
- Vce: ~30–35 V
- Ic: tens to around 100 mA
- Built‑in base bias improves tamper resistance to noise and simplifies design
Note: exact ratings and pinout depend on the specific PDTC114ET variant. For precise electrical specs and the meaning of “215,” consult the manufacturer’s datasheet.
Equivalent
Do you mean PDTC114ET? If so, it’s a pre‑biased NPN digital transistor in SOT‑23. Direct equivalents: DTC114E / PDTC114E (Toshiba, Diodes Inc., Vishay variants) and other DTC114-series parts with the same base‑resistor and hFE. Otherwise you can replace it with any NPN SOT‑23 digital transistor with matching Rbase and gain, or a discrete NPN plus an appropriate base resistor. Provide the datasheet/specs and I’ll give exact cross‑references.
Features
Here are concise features of PDTC114ET (DTC digital transistor, Tape & Reel):
- NPN digital transistor with built‑in base bias resistor and base–emitter pull-down
- No external base resistor required; can be driven directly from MCU/logic
- Ic rating up to about 100 mA; Vce up to ~30 V (check datasheet for exact variant)
- Low input drive current (typical few mA or less)
- Fast switching suitable for logic interfacing and LED driving
- Floating-input protection: defined off-state due to internal base-emitter resistor
- RoHS compliant; lead-free
- Packaging: Tape & Reel variant PDTC114ET
Note: exact Ic, Vce, and resistor values can vary by specific part variant; consult the datasheet for precise parameters.
- NPN digital transistor with built‑in base bias resistor and base–emitter pull-down
- No external base resistor required; can be driven directly from MCU/logic
- Ic rating up to about 100 mA; Vce up to ~30 V (check datasheet for exact variant)
- Low input drive current (typical few mA or less)
- Fast switching suitable for logic interfacing and LED driving
- Floating-input protection: defined off-state due to internal base-emitter resistor
- RoHS compliant; lead-free
- Packaging: Tape & Reel variant PDTC114ET
Note: exact Ic, Vce, and resistor values can vary by specific part variant; consult the datasheet for precise parameters.
Pinout
PDTC114ET (“,215” is a packaging/tape‑and‑reel suffix) is a single NPN "digital" transistor in a 3‑pin SOT‑23 package (3 pins total). Typical pin assignment (SOT‑23):
- Pin 1: Base (internal base resistor)
- Pin 2: Emitter
- Pin 3: Collector
Function: NPN switching transistor with an integrated base resistor for direct TTL/CMOS drive; used as a low‑side switch, level shifter or simple LED/relay driver.
- Pin 1: Base (internal base resistor)
- Pin 2: Emitter
- Pin 3: Collector
Function: NPN switching transistor with an integrated base resistor for direct TTL/CMOS drive; used as a low‑side switch, level shifter or simple LED/relay driver.
Application
PDTC114ET and PDTC215ET are digital transistors with built-in base resistors, used for simple logic-level switching. Typical applications:
- Direct MCU/interface drive: no external base resistor, easy logic input
- Low-side switching of small loads: LEDs, indicators, relays, solenoids, small motors (within ratings), with flyback protection for inductive loads
- Signal buffering/level shifting: buffers/inverts between TTL/CMOS and other circuits
- Automotive/industrial control: compact, robust driver for sensors and actuators
- Prototyping/education: reduces component count in switch circuits
(Adapt to specific ratings of each model as needed.)
- Direct MCU/interface drive: no external base resistor, easy logic input
- Low-side switching of small loads: LEDs, indicators, relays, solenoids, small motors (within ratings), with flyback protection for inductive loads
- Signal buffering/level shifting: buffers/inverts between TTL/CMOS and other circuits
- Automotive/industrial control: compact, robust driver for sensors and actuators
- Prototyping/education: reduces component count in switch circuits
(Adapt to specific ratings of each model as needed.)
Package
PDTC114ET,215 is a 3-lead SOT-23 (TO-236AB) surface-mount package, typically supplied in tape-and-reel.
