AD8544AR
아날로그 디바이스(주)
- Lifecycle
- Active
- Stock
- 1986 PCS
- Package
- SOIC-14
- Series
- 선형 증폭기 - 계측기, 연산 증폭기, 완충 증폭기
AD8544AR과 AD8548ARZ-RL에 대한 심층 비교를 통해 두 제품의 사양 및 주요 특징에 대한 유용한 정보를 얻을 수 있습니다. RoHS 준수 여부, REACH 인증 상태, 시리즈, 장착 방식, 패키지 유형 및 기타 관련 특성을 포함한 중요한 요소들을 자세히 다룹니다. 두 제품의 차이점을 나란히 제시함으로써 부품 선택이 간소화되어 특정 용도에 가장 적합한 옵션을 쉽게 선택할 수 있습니다.
Replacement verdict
The AD8548ARZ-RL is a viable functional replacement candidate for the AD8544AR, sharing the same quad CMOS op-amp architecture, SOIC-14 package, and wide supply range, though the lower quiescent current and reduced gain bandwidth of the AD8548ARZ-RL should be validated against the bandwidth and drive requirements of the target design before substitution.
아날로그 디바이스(주)
아날로그 디바이스(주)
Rows are prioritized by design impact. Highlighted values require attention during substitution.
Key electrical and mechanical differences between the two devices
| Parameter | AD8544AR | AD8548ARZ-RL | Why it matters |
|---|---|---|---|
| Number of Amplifiers | 4 (Quad) | 4 (Quad) | Channel count must match the circuit's signal path requirements for direct substitution. |
| Supply Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V | The operating supply window determines compatibility with the system's power rail. |
| Input Offset Voltage (Max) | 6 mV | 1.5 mV | Lower offset improves DC accuracy; a tighter spec may be required for precision signal chains. |
| Input Bias Current (Typ) | 0.1 pA | 0.1 pA | Ultra-low bias current suits high-impedance sensor and photodiode front ends. |
| Gain Bandwidth Product | 1 MHz | 1 MHz | GBW sets the achievable closed-loop bandwidth and small-signal response speed. |
| Slew Rate | 0.92 V/µs | 0.92 V/µs | Slew rate limits large-signal transient response and distortion at higher frequencies. |
| Supply Current per Amplifier (Typ) | 45 µA | 45 µA | Quiescent current drives battery life in portable and low-power designs. |
| Input Voltage Noise Density | 42 nV/√Hz | 42 nV/√Hz | Noise density affects the achievable signal-to-noise ratio in low-level signal applications. |
| Operating Temperature Range | -40 °C to +125 °C | -40 °C to +125 °C | Temperature range confirms suitability for industrial and automotive environments. |
| Package / Mounting | 14-Lead SOIC (Surface Mount) | 14-Lead SOIC (Surface Mount) | Package and footprint compatibility enables drop-in board replacement without layout changes. |
Send your BOM and application constraints for technical and sourcing review.
Use manufacturer datasheets as the final authority.
| Specification | AD8544AR | AD8548ARZ-RL |
|---|---|---|
| Supplier | - | Analog Devices Inc. |
| Part Status | Obsolete | Active |
| Amplifier Type | General Purpose | CMOS |
| Number of Circuits | 4 | 4 |
| Output Type | Rail-to-Rail | Rail-to-Rail |
| Slew Rate | 0.92V/µs | 0.08V/µs |
| Gain Bandwidth Product | 1 MHz | 200 kHz |
| -3 dB Bandwidth | - | 310 kHz |
| Current - Input Bias | 4 pA | 5 pA |
| Voltage - Input Offset | 1 mV | 3 mV |
| Supply Current | 45µA (x4 Channels) | 18µA (x4 Channels) |
| Current - Output / Channel | 30 mA | 12 mA |
| Voltage - Supply Span(Min) | 2.7 V | 2.7 V |
| Voltage - Supply Span(Max) | 5.5 V | 18 V |
| Operating Temperature | -40°C ~ 125°C | -40°C ~ 125°C |
| Mounting Type | Surface Mount | Surface Mount |
The AD8544AR is a quad-channel, 1 MHz CMOS rail-to-rail operational amplifier supplied in an 8-lead SOIC package (R-8 suffix), while the AD8548ARZ-RL is a quad-channel, 1 MHz CMOS rail-to-rail operational amplifier supplied in an 8-lead SOIC package in tape-and-reel form (RL suffix) with a lead-free, RoHS-compliant finish (Z suffix). Both share the same core amplifier architecture and pinout; the primary differences are packaging format, lead finish/qualification, and the associated ordering code.
Functionally, both are quad 1 MHz CMOS rail-to-rail input/output op amps with the same pinout in an 8-lead SOIC package, so they can typically be interchanged in a design that already uses the SOIC-8 footprint. However, the AD8548ARZ-RL is the lead-free (Z) tape-and-reel (RL) variant, so the designer must confirm solder process compatibility, moisture sensitivity level, and any qualification differences against the respective manufacturer datasheets before substitution.
Both the AD8544 and AD8548 are specified for single-supply operation from 2.7 V to 5.5 V (and dual supplies within that range). The AD8544 datasheet specifies a typical supply current of approximately 45 µA per amplifier (about 180 µA total for the quad) at 5 V. The AD8548 is a lower-power variant; designers should verify the exact quiescent current from the AD8548 datasheet, as it differs from the AD8544.
The AD8544 has a gain bandwidth product of 1 MHz and a slew rate of approximately 0.92 V/µs. The AD8548 is specified with a similar 1 MHz gain bandwidth product class; the exact slew rate and AC specifications should be taken from the AD8548 datasheet, as the two parts are distinct data sheet entries and parameters should not be assumed identical.
Both are rail-to-rail input and output (RRIO) CMOS amplifiers, allowing input common-mode voltage to extend to both supply rails and output swing to within millivolts of the rails under light load. This makes them suitable for low-voltage, single-supply signal conditioning where full dynamic range is required.
The AD8544AR uses the R-8 suffix denoting an 8-lead SOIC package in tube or standard reel form. The AD8548ARZ-RL uses the Z suffix for a lead-free, RoHS-compliant finish and the RL suffix for tape-and-reel packaging, which is preferred for high-volume automated assembly. Both are 8-lead SOIC (narrow body) devices with identical pin assignments.
Typical applications include portable and battery-powered instrumentation, sensor signal conditioning, active filters, photodiode amplification, medical monitoring equipment, and low-voltage data acquisition systems. Their low supply current and rail-to-rail I/O make them well suited to space- and power-constrained designs.
Both the AD8544 and AD8548 are specified for the industrial temperature range of −40 °C to +125 °C, making them suitable for industrial, automotive-adjacent, and outdoor instrumentation applications. Designers should confirm the exact grade and temperature specification from the specific datasheet revision for each part number.